I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hello Nordic! Regarding Notifications on the s110, once sd_ble_gatts_hvx(conn_handle, ¶ms) returns NRF_SUCCESS , how long does it take, at most, in units of CI (Connection...
Dear sir.
I have question of SPI slave communication.
[NRF_SPIS1->TXDPTR] is a point to address of TX buffer.
After [spi_slave_buffers_set] is called and SPI transaction...
I've successfully compiled, flashed, and run the SDK11 ESB examples on nRF52 DKs using GCC, and am trying unsuccessfully to get them to work on the Keil 5.20 IDE.
I've...
I tried to get the ble_app_proximity example to work today, with either the nRF51-DK, nRF51-Dongle or nRF52-DK, along with the Nordic Connect app on Android.
I encounter...
I am working on application where the nrf51 will read information from several sensors and send the data to a smartphone app via BLE. Among the sensors are one that sends...
Hi, I am trying to get my ble400 board working with nRF51822 chip. I downloaded SDK v11 and made all nedded preparation. I have successfully compiled blinky app, and everything...
Hi Nordic Tech support team,
I'm Hardware design engineer and working on wearable IoT design and would like to implement OTA programming for nRF52832 Bluetooth SoC.Kindly...
this is my code:
this is BLE_peripheral UART and i added these lines to main():
my soft device is S130 V2 alpha
// Initialize.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE...
I'm working with the nRF8001, at present using the RedBear BLE Shield.
My current issue is that after starting to Advertise, but before a connection is made, I wish to...
Hi,
I want to write a firmware for one of our products with on nRF51822 QFAC included.
I downloaded the SDK v7.2.0 and I want to use the ble app hrs project as a starting...
Hi,
Currently working on nrf51422 with s130,I have currently been able to transmit 20 bytes of data at 100ms interval to mobile.But when I decrease the duration of tranmission...
Hello,
I am trying to use uart port on pca10040,
Connected tx,rx pin to FTDI USB Serial Device converter .
Disconnected the usb cable, device is now powered over...
I want to use the pwm to control buzzer, but when I use init function, the power will increase 880 uA, how to decrease the power.
void beep_on(void)//beep on
{
app_pwm_channel_duty_set...
Hello,
for my project I'm using: SDK11, s130, nrf51 (nrf51822-QFAC), central and peripheral roles, DFU.
I've managed to have both peripheral and central roles with DFU...
hi, i am using eclipse IDE to implement ble_hrs example. while i am calling ble_stack_init() from main function. in the ble_stack_init() function UNDER THE macro SOFTDEVICE_HANDLER...
