I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello,
Since 2 weeks, I use heavily my nRF51-DK (PCA10028), with mbed compiler to make a BLE enabled device.
But, since few days, when i have tried to cut the SB9 in order...
I have a Rev3 nRF51822 chip (CFACA00) on a custom board (no external pull resistors on SWDIO or SWCLK), and I am using nRFgo Studio 1.20.0.2 to program SD 8.0.0 and my Nordic...
I'm using Python bindings 0.5.0 and the connectivity app. On one of our machines that is running tests with the satck/dongle we see it fail a lot with a scrolling of this...
I want to extend the ble_app_multilink_central for pca10028 Example to be able to communicate with a sensor via SPI and then initiate a connection with another pca10028.
...
I'm trying to discover a vendor specific service that has 7 characteristics. However, when I increase BLE_DB_DISCOVERY_MAX_CHAR_PER_SRV to 7 , ble_stack_init() hard faults...
Is it possible to use PPI and RTC to turn the HFCLK on or off ? (external Xtal)
Example - something like this ...
NRF_PPI->CH[9].EEP = (uint32_t) &NRF_RTC0->EVENTS_COMPARE...
hello,
when I use the chip nrf51822(3rd generation),I find that when I open DCDC function,the ability of chip receiving msg is weaken.the receiving distance is shorter a...
I am doing a blob read on two s130's with s120(central). I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE event while doing a continuous blob read.
Some times i get BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
I would like to have 31 bytes for my own in advertising and so far I have disabled everything except adv_flags (it still takes 3 bytes cause of length, AD type and value)...
Hi there,
just wanted to know what the practical differences between the JLINK and mbed MCU interface firmwares are.
From what I experience I can only use the UART over...
