I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, We have a device configured as a peripheral and want to provide the user with the peer device name typically connected to it, like the device name. Typically a phone will...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands(READ, WRITE, etc.) to the IntanRHD2132(ADC) at regular...
We have a sudden problem with the flash_manager. The code stops at static uint32_t flash_area_build(flash_manager_t * p_manager), at line NRF_MESH_ASSERT(p_manager->config...
Hi.
I am designing a 4 layer PCB (0.8mm thick) for an nRF52820 microcontroller.
My board's stack: L1 - Signal L2 - GND L3 - Power L4 - Signal
I have questions regarding...
Hi dear forumers,
I'm in the goal of achieving lowest current consumption on my PCA10056 DK board, with an nrf52840.
I converted a previous zephyr firmware who perfectly...
Hello, I am using the nRF5340 Audio DK with Zephyr and want to use I2S to send audio to an I2S device. So far I have had little success with the microcontroller halting in...
11 months ago in an answer a nordic member wrote (in regards to an error that I now also had and could solve using CONFIG_DEBUG=y):
[quote userid="81283" url="~/f/nordic...
Hi there,
I have an issue when using PPKII software on MacOS at 100ksps (no issue at 1K):
The 10min button at the top does not appear anymore
After a 3min measurement...
Good Afternoon,
I'm designing a 4-layer PCB based on an NRF52832 (QFAA) paired wit h a Molex 479480001 SMT Antenna, and I was hoping for some feedback on Antenna Matching...
Hello,
I'm trying to sniff packets with wireshark by varying the connection interval and supervision timeout of my ble application. I see that with lower connection intervals...
I'm presenting an issue when exporting the data collected, specifically the digital outputs, they are exporting incorrectly, but in the Data Logger tab they are presented...
When implementing AWS_IOT provisioning by claim process, AWS_IOT responds to the published topic $aws/certificates/create/json with a 3580 byte response. This causes TLS to...
Hey, I'm pretty new to Nordic Development. I am working on nRF5340 Audio DK development board right now and I was trying to create a bluetooth speaker kinda setup using the...
Regarding the design issues with the nRF5340, I have adopted the nrf5340_qkaa_config3 design scheme from the hardware design package. However, after testing, I found that...
