Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Using the Zephyr logging system, setting Kconfig option in prj.conf to override logging to level 4 (output LOG_DBG messages) breaks the console and no output is sent at all...
Updating to NCS 2.1.0 the CONFIG_ADP536X_BUS_NAME is still defined but seems to be not longer valid.
The "adp536x.h" is now in the includes. Is there a supported way to...
Hi.
The LE Audio Controller Subsystem for nRF53 used by the nRF5340 Audio example as I understand it, is only available as Hex file.
Is this controller based on the Softdevice...
Hi friend,
I am using SDK16.0 and softdevice is S140 7.0.1 version. But SPI can only send out 1 byte. It can't call back the function of spi_event_handler, so my code is...
Hello everyone,
I have successfully managed to perform a DFU with a DFU package consisting of an app and a softdevice. I wanted to test what happens when I manually cancel...
Hello all,
I was programming the nrf9160 SiP using esp32 over UART and wanted to know how do I connect ESP32 to the nrf9160 SiP and upload the code through ESP32 over to...
SLM returns ERROR after AT#XSOCKETOPT=1,51 NRF_SO_RAI_LAST https://github.com/nrfconnect/sdk-nrfxlib/blob/main/nrf_modem/include/nrf_socket.h#L218
SLM returns OK for AT#XSOCKETOPT...
Hello I am using I am NRF SDK version 1.8.0 and nrf-zephyr v2.7.0-ncs1 (If a soultion exists on newer a rev, willing to upgrade now, otherwise it will happen some time in...
When PIN=0 P0.00 is used it doesn't work (No error message or failing, i also tried several other ports), no toggling output. The code works with PIN=28 (P0.28=LED1), led...
It is properly pointed to in the emProject file, and the SES IDE is able to locate and open it in file explorer.
I upgraded the liboberon to 3.0.8:
When I previously...
I have a successful build over my i2c application but, I do not get any text output on the console. So, to check I tried to build a new hello world project and run it but...
I'm attempting to use the "powf()" function in a Zephyr thread.
When I try to run:
LOG_INF ( "powf: %f" , powf ( 2.0f , - 8.0f ));
the result is "inf". (Code compiles...
