Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello, we have a project in nRF Connect SDK, where we'd like to use a separate .conf file for b0n subimage in a multi-image build,
Let's say it's called b0n.conf. So, before...
Hi,
I would like to ask is there a dll file and header (.h) file for the nRF Connect Desktop Bluetooth Low Energy software? I am seeking for a chance to apply it in the...
Hi Good morning
Could you please to know the reccomendable dimentions of pad for soldering, dimentions of pad, PCB Layout for soldering component.
For example the component...
I was running Ubuntu 18.04 and Actinius Programmer was able to upload an example firmware without a problem. However, I upgraded my computer to Ubuntu 20.04 and Actinius Programmer...
I have used nrf5340 audio DK with nrf\applications\nrf5340_audio\bin\ble5-ctr-rpmsg_3251.hex in net core and zephyr\samples\bluetooth\hci_uart in app core directly after receiving...
Hello,
I want to install NCS 2.1.0, but I get the following problem.
I used toolchain manager 1.2.0 to install NCS 2.1.0. Open VS Code is now available.
I opened...
Hi,
I have a question, I use a 52840 board as the Bluetooth center. The protocol is S140. The other 51822 board is a Bluetooth peripheral. The protocol is S130. The routine...
Hi! We are trying to understand how UICR registers work. In particular APPROTECT, ERASEPROTECT, and SECUREAPROTECT.
We are trying to find a clear explanation for this image...
Hi ..i'm using nRF52832 interfacing with BG95(QUECTEL) ..when i insert my sim in the module at the time uart receiver is not working..when i remove the sim at the time uart...
hello
iam trying to add services in the buttonless dfu from one of the sample code im not able to come up with the services after lot of efforts and now im getting this...
Hi There,
I would like to extend the NRF9160 LED CAF by using the WS2812 LED instead of 3x discrete LEDs.
1. Where in the CAF or Zephyr or wherever, are the function calls...
Hi, We are trying to work with nrfxlib directly baremetal without Zephyr. Were able to do advertising with it. On nRF52832 the SDC crashes when we tried to set new advertising...
Dear all,
I am developing a bluetooth mesh sensor with the NRF52833 and NRF Connect SDK.
The sensor is battery powered. So the power consumtion must be as low as posible...
