Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello,
I am using the RADIO peripheral to send BLE 4 advertising packets back and forth between 2 DK's (nrf52840 as transmitter, nrf52833 as receiver) following the radio...
Hi,
Nrf52 52840DK,SDK17 S140.
how to broadcasts continuous data? (Continuous broadcasting, with different data each time)
code as follows:
SDKs\nRF5_SDK_17.0.2_d674dde...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
In our BLE connections we often receive a BLE_GATTC_EVT_WRITE_RSP event with gatt_status 0x01F2.
Looking at the list of GATT_STATUS values, this must be an error in the...
Hi, based on my previous posts ( 2nd post , 1st post ) regarding the ble_app_uart_c multilink example I now face another issue.
When I run the multilink example on my nRF52840...
Hello,
Until now we compiled our company project using SEGGER Embedded Studio command line tool 'emBuild' that was called from a custom Makefile like this:
But we...
Hi all,
I want to self provision my node. I am using nrf52832 dev board, mesh SDK v 3.1.0, light switch client example. You may wonder why self provisioning, when there...
Hi, I am currently utilizing an app that supports multi link; however, I was only able to get 7 maximum stable connections. My goal for this multi-link is to connect a sensor...
Hi,
I am trying to run the DNS example provided in the Nordic Infocenter as part of the Thread Border Router setup, but it is not working. I am getting "Error 28: ResponseTimeout...
Hello,
I tried to implement the HX711 example from Vidar mentioned here ( https://devzone.nordicsemi.com/f/nordic-q-a/34112/best-approach-to-interface-hx711-with-nordic...
