I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have an issue with creating a Bluetooth mesh gateway. It would be better to use nRF Connect SDK for me, but nRF5 for Mesh is also fine. As I've found among answers, not...
Hello guys,
I try to implement a pdm sensor on the nrf 52 dk which sends the audio data to a central device.
My setup is two nrf 52 dk one acting with the modified ble...
Hi,
I am developing application in nRF_connect_SDK v 1.4.2.
I have a problem in Debug the code 1. When i debug the code the breakpoints is not appearing
2. When i...
Hi Nordic,
how do i interpret properly return errors? I l know that it depends on the base address but sometimes it does not correlate at all.
For example, currently...
Dear friends,
We want to update the bootloader in our project. I have read the tutorial about the DFU process from here " Dual-bank and single-bank updates ". I have some...
Hello I would like to change from nrf52810 to nrf52805. I want to take the same code, but I want to change only the gpio because the gpio is different. I was going to set...
When I try to connect to my Pure-FTPd server I always get an error when trying to login, but If I use a public server like... https://dlptest.com/ftp-test/ it's fine. This...
Hey all!
We want to improve the accuracy of the localization of our asset tracking solution, in particular indoors. For that we want to scan Wifi base station advertisments...
Hello,
I am trying to get an MQTT TLS connection to AWS up and running on my thingie91 (nrf9160). I am using SDK 1.5.0 and the sample "aws_iot".
Even though there is a...
Hello,
what is the CPU speed of nRF52832?
I'd like to test if the NRF52832 is running at 32MHz or 64MHz.
I used it to run a compression algorithm, which took 8ms to...
I have seen this question asked a few times--but every thread seems to have no concrete answer.
I have uninstalled and reinstalled all JLINK drivers.
But still get the...
I am using the nRF9160 for IOT with the console connected on UART 0 there is a string of +CSCON: 1 and +CSCON: 0 messages displayed.
Build Zephyr 1.5.1
Modem firmware...
We're looking for some clear documentation for implementing OTA DFU via BLE on the iOS side. We have the firmware working well on our dev kits here, but working only with...
