When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Below is the output from a 'bluetoothctl' session for one of my thingy:52's
This is running on a raspberry pi 4 using Ubuntu Mate 20.xx
The output below is using command...
In beacon example code the RSSI value is 0xc3 while converting to decimal it giving 195 and in comment line it is mentioned as dbm.when converting this 195dbm to milliwatts...
hi,
The Fanstel BT832 has a nRF52832. It has TX on P11, RX on P12 for standard uart. I need however rs485 and so need to add a DIR (output) pin. P11 and P12 are not on...
In the mRF24L01+:
Unlike MultiCeiver mode, I have one TRX and multiple PRX units sending back ACK payloads.
In the PRX, what is the purpose of the PPP field in the W_ACK_PAYLOAD...
Hello,
As I understand it, Apple is working on a new product called Airtags. This will be similar to the Tile for finding items like your keys or wallet. The catch is that...
I'm using standard ble_bas from sdk12.3. I set up a timer at 60s interval to use saadc to read battery voltage. Below is my code in saadc event handler for battery level update...
Hi,
I want to add some included services to a new added custom service with nRF Connect, but I can't find a method to do this.
Is there a method to solve this problem...
Hello, regarding to another thread in this forum the debug interface mode can be turned off by sending the command "writeDP 1 0" via J-Link commander or by power cycling the...
Hello,
I'm working with the nRF5 SDK for Mesh v4.2.0.
During the init phase, I call the function mesh_stack_init()
After doing so, the consumption is on average 2.8...
Hello DevZone,
SDK 15.0.0 SD S140
Currently working without an active SoftDevice but even with an active SoftDevice these problems keep occurring.
I'm currently working...
Hello! I need help implementing a TDMA on a nrf52. I've never done this before and Its been hard to find good resources online on the topic so if anyone here has any previous...
I am developing connection between BM833AF Evaluation board and nRF52840, Like a BLE Tag and Beacon. Need support in connection and transmitting data from one to another?...
Hi,
My use case is I have an RGB LED that I want to be green for normal operation, but blink red for 0.5s when a serial driver error occurs.
R, G, and B are each attached...
Hello,
I have multiple questions regarding BL mesh using nRF5 SDK for Mesh v4.2.0
1) is it possible to run this example using 2x NRF52840 dongles(PCA10059) and one NRF52840...
Hello
We have an application that ADV every second and is based on SDK 14.
We are currently attempting to move to SDK 17. What I have noticed is that if I change and...
