Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I'm currently working on u-blox Nina B302 and I'm trying out program examples from the nRF52 SDK on an evaluation board. To try out BLE connections, I'm using the nRF Connect...
Hi
The Product (NRF52832) was upgraded from SD 4.0.2 to the SD6.1.1.
During the pairing procedure the sd_ble_gap_data_length_update() returns a NRF_ERROR_RESOURCES error...
I use SDK16.
test fstorage write data.I find fstorage is busy appears when BLE sends and receives data.
for example main.c :
line 206: fst_erase_test(); line 207: NRF_LOG_INFO...
I am trying to implement the Simple On Off Server model in an existing project. In main.c I did the following:
1. In models_init_cb(), I added the following lines:
2...
Hello. I'm trying to make a product by running nrf51822 as an observer role.
This product will only use passive scanning and will not transmit any data.
How much energy...
Hello,
I have some issues sending valid information to nRF Connect app by bluetooth using the Aduino Nano 33 BLE with nRF52840 on it. I am using Arduino IDE and the ArduinoBLE...
Hi all,
The project I am working on consists of a BLE peripheral, a BLE central and an enhanced shockburst device. I run into a problem in the code of the peripheral:...
In a project based on Softdevice S132 7.0.1 employing the Softdevice timeslot API, I noticed that the nrf_radio_signal_callback_t function passed into sd_radio_session_open...
Hello,
I am using UART_1 to receive GNSS data. For UART_1, baud rate is 115200bps. On terminal, I can see the correct data when baud rate is set to 115200bps. When the baudrate...
Hi, i am using nrf52840 development kit , four servo motor . using 15.2 sdk version
here i am controlling the angle using adc values , i am done with one servo motor . pwm...
Hi
I am modifying the scanning and advertising paremeters for coded (125kbps).
I made the following changes in advertising
.primary_phy =BLE_GAP_PHY_CODED, instead of...
Hi All,
I am using nRF52832 SOC for my development. I would like to buy a packet sniffer for my BLE development.
Can someone please suggest a suitable device for this...
Hi
In the SDK, Replay_Cache_Entries is assigned a value of 40, which means that Replay_Cache can only process 40 unicast messages. That limits the maximum number of unicast...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
Device has both Central & peripheral functions.
It takes about...
