When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I noticed that the v1.1.0 modem firmware download includes an A/B set of differential images for doing testing, but not a 1.0.1-to-1.1.0 image. Could I possibly get one? I...
I have to folders with different versions of the nrf library installed (1.0.0 and 1.1.0-rcsomething) The dts and overlay files are identical in the 2 folders (nrf9160_pca10090ns...
I have taken a new Thingy:91 out of the box, fitted ibasics sim card and been through the registration process. Sim registers fine, but the 'add new LTE device' does not recognise...
Can you tell me which Heart Rate monitor gives 0x2A37 is the UUID for the Heart Rate Measurement characteristic. The heart rate service is 0x180D. Battery service is 0x180F...
How can I add debug and release configurations to the "mqtt_simple" project?
Video tutorial "SEGGER Embedded Studio - Build configurations" does not show this important...
Hi Devzone!
I'm using nrf52840 custom board to launch iot service.
We have two type of devices. One is master and the other one is slave.
For now, both of them...
In nRF5 SDK 16 (downloaded file nRF5SDK160098a08e2.zip), the components/boards/pca10059.h file is missing the LED_START and LED_STOP defines that are present for other boards...
Dear Nordic,
I have a 4MB external flash on my board, I've successfully run the code on it by using XIP. However, I got stuck when I was trying to read back data from...
The bug shows when executing an application in RAM with nrf52840. Using SDK 16 but seems to show in older versions also.
The below function code is the first level of...
Hi all!
Everywhere it can be read how important the dimensions of the groundplane are for a well working antenna... but what are the right dimensions? And where is the best...
Multilink S132 central should handle connections to multilink peripherals which do continuously advertise. Once central got first adv event from such peripheral it establishes...
Hey,
As a student currently I'am working on a project for my universitiy. I want to use the nRF51822 for Bluetooth low energy communication.
In the datasheet is written...
Hello Everyone,
I'm involved in a project where we are evaluating ble mesh and Thread mesh on nrf52840.
I want to know, does Nordic supports ble mesh and Thread mesh simultaneously...
When using Keil Compiler, I am unable to compile any of the ble_peripheral examples. I get an error that says...
RTE\Device\nRF52832_xxAA\system_nrf52.c(29): error: #5...
Issue with NRF52832 Firmware installation
Hi We are developing custom boards with nrf52832 chip, and it is working well.
The issues occurs when installing firmware without...
