When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I have and nrf5340 connected to debian system via uart. I'm trying todo a flash update via the uart and the nrf5340 is unresponsive. The MCUmgr is not getting any response...
Hi there,
I'm using /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding/connected_cs/initiator and /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding...
Issue
How to properly wake an nRF54L15 from System-Off mode when the device receives a UART transmission, without the use of the LPUART Ready and Request lines or any sort...
Board: nRF52840 DK (pca10056) NCS version: v3.2.3 Goal: Send and receive raw 802.15.4 frames with a custom packet format, without using OpenThread, Zigbee, or any other mesh...
When attempting to install a downloadable app in nRF Connect for Desktop 5.3.0 on Linux, the installation fails with an EISDIR: illegal operation on a directory error. The...
As mentioned in subject,I try to study course with CMSIS-DAP,now, chip recove and flash is OK,but blocked at debug step for 2 days now.
Maybe I made some wrong config some...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
This question concerns the description of the SPI communication Electrical Specifications on page 425 of the nRF52840 Product Specification.
The values for "t_spim_vmo...
Hello,
I have a product with QSPI flash that I would like to use nrfjprog to program the flash part. However, the QSPI flash's VCC is controlled (via a FET) from a GPIO...
Summary
With CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and CONFIG_OPENTHREAD_TREL=n , the Zephyr/NCS build fails to link:
ld.bfd: ... openthread_platform.a(trel.c.obj)...
Hello,
I am currently working on a new design based on nRF9151. This design is the evolution of a previous PCB.
The device uses a combined GPS and Cellular antenna, which...
Subject: Support Request for nRF7002 Integration with ThreadX on STM32
Hello Nordic Team,
We are currently using the nRF7002 with our STM32-based device. We have completed...
I am using nrf52832, and I want to use SYSTEM ON Sleep. Also , my wake up sourses are timer based, and also GPIO interrupt based. But I observed that the device cannot go...
