I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
What is the timing of the indication retry mechanism (SDK14.2, nRF52832) ?
App use sd_ble_gatts_hvx() to schedule message for sending
At the next connection interval...
Hi, Great Nordic Support teams:
I'm wondering if the only limitation of the choice of L3 on nrf52832 layout is just the tolerance under 10%?
Cause it seems to be the...
Hi,
I've recently enabled the watchdog in our project which included buttonless DFU. Project is based on FreeRTOS, SDK14.0, S132 v5.0.0 on custom board nRF52.
Since the...
Hi All,
I'm running a windows box with Android studio with the GitHub Thingy Repo https://github.com/NordicSemiconductor/Android-Nordic-Thingy project downloaded. The project...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about SPIS and SPIS event "NRF_DRV_SPIS_XFER_DONE".
1. What would trigger event...
HI,
In need to generate a sweeping tone to drive a piezzo element, i determined the tone should be sweeping back and forth between 2.5KHz and 4.5KHZ at an approximative...
My ultimate issue is trying to get a bootloader working on custom hardware with an nRF52832. The bootloader is mostly the base UART DFU bootloader from the Nordic SDK, with...
Hi,
I'm able to run the DFU mesh from the quick guide and now I want to integrate the DFU into my application.
My application is based on the light switch example, so...
Please help me fix my computer to allow nrfStudio to program pca10056.
I just received 2 pca10056 1.0.0 2018.35.
I am on 2 computers A and B: both with windows 10 64bit...
I trying to debug an interaction between using SPIM3 on the nRF52840 and the BLE stack in the SoftDevice . A reset is happening, which I think is being generated by the SoftDevice...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
