Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
hi ,
I use SR3 V1.2 to test. I enable ANR, play the recording directly in the loop.
About every five seconds, a second or so of unusual sound appears. The rest of the...
Hi,
I can't understand what is DFU example inside /examples/dfu folder and what is /bin/bootloader/? I read DFU quick start guide, but where is source code of bootloader...
I try debug my app in keil debugger but it's often raised app: SOFTDEVICE: ASSERTION FAILED in SEGGER after step down through the code (in few steps).
My app based on buttonless_dfu...
Hi,
I have a doubt regarding buffer setting in SPIS.
In the SDK15 SPIS example, buffers are set using nrfx_spis_buffers_set(...) and it works perfectly.
I was wondering...
Hi All,
I am using nrf mesh SDK v2.2.0 and nrf SDK v15.0.0.
I have created a new model in nrf mesh SDK, this model is publishing scanned data on group address.
When...
Hi,
I was working on the HID mouse example and noticed that the example gets disconnected from my mobile phone once i start moving the cursor.
I also noticed that the...
Hello,
I am performing current measurements on custom hardware with the nRF52840 and comparing my results with the values in the nRF52840 product specification. I noticed...
I have downloaded nrf5_SDK_for_Mesh_v2.1.1_src and tryign to build the client and server example to test the Lighting Mesh example from the Android/iOS apps available on the...
Dear Nordic Team
I have changed pwm driver example as you see in bellow . i also observed the codes which you linked for pwm. Bellow code works without the effect of update_pwm...
We are trying the HID Keyboard example using SDK 12 with no modifications on the nRF52 (PCA10040) board. We are able to pair and connect on both iOS and Android the first...
Hi,
I have a nrf52 DK. I currently tested apps on run smartphone. Similar to nrfconnect, toolbox, uart.
Laptops also have bluetooth. Can i use laptop's bluetooth to communicate...
Hi, I would like to create a new target,but nRF52810 only can be compiled with makefile and I don't know makefile too much.
I try to edit the makefile with my own target...
Hi guys,
I'm using following setup NRF51822, SD130, SDK 12.3.0. I control one transistor with PWM output via timer 1. Before enabling PWM I start 8bit ADC task to measure...
Does the Nordic UART Service (NUS) have a facility to confirm when a sent message has been received by the peer?
In particular, to confirm when an NUS message sent by a...
Good afternoon,
We are using NFC on nRF52840 (Type 4 Tag, SDK15.0.0, Softdevice6.0.0) to exchange some data and we would need to be able to do the following, please let...
