Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello,everyone,
I have successfully installed nrfutil using pip install nrfutil, but when I type nrfutil in the terminal, it shows -bash: nrfutil: command not found, how...
Hi,
We were trying out the long range central and peripheral examples found in github with the nRF52840 DK boards but we are not getting the specified range(We did switch...
Hi everyone, I have nRF52840 DK and I want to write an application program that uses multiple wireless communication protocols (e.g BLE , Zigbee , Thread) and can communicate...
Hi,
I am trying to add Nordic UART service(NUS) in ble_app_relay_rscs, but after adding nus service in application device is not advertising and there is no print in serial...
Hi! I am trying to read the voltage of a LiPo battery as explained in this blog post. The code on github however, is not compatible with the latest SDK for the SOC (12.3)...
Hey guys,
we are currently evaluating the pc-ble-driver-js. We want to get it running on a Raspberry Pi 3.
The Nordic nRF52840 module was flashed with SD Version 6.1.0...
Hi,
i am using nrf51822 interface with mpu9250 and i want to detect a tap without using of DMP feature of mpu motion sensor. my application requirement is low current consumption...
Hi,
sending some data from nRF52840 (DK or dongle) to a host computer via USB. When nRF52840 is connected to a "powerfull" host, all goes ok; when connecting to a "less...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
hello,
Now i transplant pwm_library programming to ble_app_uart_c(central) in SDK15.0.
But i found the program cann't run in NRF52 DK.
I found it build no errors but...
Hello,
We are evaluating now a new project and I am struggling to get a feeling about one moment of Thread network and its particular implementation with nRF52840.
In...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
