Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Dear Nordic DevZone,
I am having a problem using SEGGER Embedded Studio for ARM
Release 4.12 Build 2018112601.37855 Windows x64
When I select a Group under Registers...
I have ported the NFC URI example to a custom project that I am working on (platform details listed below). I am using an Android phone running NXP tag info app to read the...
Hello
I have a question to ask, I want to beacon the battery level and temperature. I know there is a temperature sensor inside, if I want to use saadc to get the sensor...
Hi All,
I compiled Keil UART application and it is working fine on Eval Board. But the same code I started running on customized board and here am getting only 1 byte every...
Hi there,
I am adding schedule to my application calling app_sched_event_put() inside a context interruption from Button to enable a sequential write to a memory using SPI...
Hi,
I’m trying to use the SAADC on nrf52832. I’m not using softdevice (I’m not doing BLE code) but it’s present on the chip (to use it for DFU). When I program the chip...
Hi I am using the nrf51422_XXAC device. I want to make a connection with my app alone. other apps should not be able to connect. please help me with sample code. I am new...
Hello,
I'm having issues trying to connect to a third-party peripheral (called iTag from now on).
I have an NRF52832-based device running as a central. My device is running...
Hello Nordic Devzone,
I have a few queries regarding using VID& PID for a hardware.
Is there any cost involved when using the Nordic VID & PID?
Will Nordic provide a...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hello.
I have a nRF9160DK.
I want to try this uart example: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
I want to config the...
Hi everyone,
I want to transmit a HEX array I read from a peripheral using SPI communication (I initialize my RX_BUF in the SPI_EVT_HANDLER() function) via BLE. I am using...
Hello All,
I am working on nRF52810 custom board. I used segger studio in windows 7. For reference i used nRF52 SDK 15.2.0.In my application i used i2c peripheral.
My...
Hello,
as I understand the accuracy of the LF Crystal oscillator for the nRF52832 development board DK_PCA10040 ist set within the sdk_config.h in the following way:
...
Using NRF52832 on a custom PCB with 32kHz + 32MHz crystals, very close to the reference schematic
Using NRF52 15.2.0, S132, arm5_no_packs, Kiel uVision 5.23.0.0
The example...
