Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi there, nRF52840-Preview-DK, 0.9.3 2017.43 nRF5_SDK_15.2.0_9412b96 IAR for ARM 7.60.1 Windows 10 Home Version 1803 OS build 17134.590
When I try to run secure_bootloader_usb_mbr_pca10056...
Hi,
In Mesh Profile v1.0 section 3.7.5.2 Acknowledged message one can read the following text.
"... If the acknowledged message has TTL set to 0, it is recommended that...
Hello,
I purchase nRF51822 Bluetooth Smart Beacon kit.
How to load the new program into this board.
I downloaded nRF51822 Bluetooth Smart Beacon kit firmware files...
Hi,
is there a simple way to enable serial logging instead of rtt in a mesh application for nrf52840DK, as example in the light switch server or client mesh applications...
On our custom board it can happen that an ASSERT triggers (suspect UART error due to EMC injection) on the connectivity chip, this meas that the application controller is...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
Hi,
I have an app that uses freeRTOS
My app runs OK , however when I am debugging it in segger studio with my SWD connector, it crashes with no reason
If I check the...
Hi All,
(Segger IDE SES Ide version = 4.10)
Various posts have attempted this, some claiming success with the following tools command :-
"$(LINTDIR)\bin\pclp64...
I'm in the process of trying to port my SDK 14 project to SDK 15.2. I've made a pretty good amount of progress, but I have two issues that I can't seem to figure out.
The...
How do I find where else in the program pin 6 is being used and disable its other functionalities in the BLE_UART example?
I am trying to read data from a sensor via SPI...
Hi, I am a novice and need help to get stated with Segger and the nrf52DK. I have installed the latest SDK 15.2.0.
I have manage to run couple of exemple with no or only...
Hi,
I am using nRF52832 chip with SDK15 and S132 softdevice.
I want to change manufacturing data dynamically in advertising frame. I would like to know step for that with...
Hi all!
I've read that nRF9160 DK comes with modem configured as LTE-M.
At the moment in Spain, only have NB-IoT coverage so... how should we do to setup the nRF9160 as...
Hi,
I would like to obtain printf and NRF_LOG separately from two TX ports.
I made a test application of serial output based on blinky.
P0.06:TX (and P0.08:RX) were...
I'm working on the project where data from nRF52840 need to be send to Android over wire. The customer does not want to use BLE.
I can connect nRF52840-DK development board...
