Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello everyone, I've followed the following guide for mesh dfu and had no issues with the example provided here : https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK...
Hello,
is it possible to set the sniffer/firmware to follow the central device instead of the peripheral?
Currently, only peripheral devices are shown in the device...
I'm attempting to get a grasp on how much CPU time an SAADC conversion is taking. I'm running the SAADC sample code from the nRF52 v15.1.0 SDK on an nRF52832. SAADC_CONFIG_RESOLUTION...
Hello everyone, We want to program the other NRF52832 chip from the NRF52832 chip via OTA. The DFU service UUID is 16 bits (0xfe59). However, the characteristic UUIDs are...
Hi,
I'm using the nrf5283 chip alongside with the SDK12.1. I have a strange situation related with the bootloader dfu.
First I flash with the programmer a merged hex...
Hello,
I'm working with Mesh SDK 3.1.0.
I made some changes in app_level.c file.
Could you please confirm that these changes are right?
They seem to work fine, but...
I am using SDK 15.2
I downloaded both nRF Toolbox and nRF Connect applications on my phone (Lenovo K6 which is running Android 7.0 but i tested the same thing on multiple...
Hi,
I'm attempting to flash program a Nina B112 Bluetooth Module (from Ublox), which is built uppon a NRF52832 board and i'm attaching this module to a custom board.
I...
Hello,
I'm building BLE preipheral and central devices for transmiting voice signal (best audio quality is not very important requirement) from peripheral to central. I...
Hi All,
We are in evaluation phase of a project where in our battery powered device would use nrF52840 MCU and communicate to the mobile phone over BLE (say about 5x times...
I am working on nrf52832 and sdk11. I want to store my accelerometer and gyroscope data into external memory.Does anyone have code of it? or any one having .c and .h file...
HI, I am using nrf52832 soc and i develop our own module. i need to create a mesh network within the device.
I am using segger embedded studio 3.34 (windows 10) and SDK...
I am new to BLE and want to learn what options and methods I have available to alter the advertisement package. Is it possible to include a floating point value, that could...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
