I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hello,
i'm developing an interface based on nrf52. The app does a direct connection, performs some exchanges with the peripheral, and tells the peripheral to disconnect...
Hello we have a more stable external reference voltage source than the VBG for the ADC we want to use.
The voltage itself is higher than the allowed reference voltage specified...
Hi,
i am working on a project that in it i had developed a firmware for nrf51844 based on soft device 130 v2.0.1, now i decided to move the project on nrf52840 . i had read...
Hi! I did see a post about this, but is there a way to implement any kind of throttling/flow control over the Nordic UART service?
About the only thing I can imagine is...
Hi,
how can I publish a message to unicast address from a generic on/off client with mesh sdk?
How can I set the address?
Jost to be more precise, the function:...
After installing the USB driver for the nRF52840 dongle and using it successfully, and then connecting the nRF52832 DK it fails with "error occurred when opening port. Errcode...
Hi everyone,
I was trying to use QSPI interface with the on board external flash memory MX25R6435F on nrf52840 PDK
This is what i have observed, Inside the linker tab...
Hi, I have nRF51822 Board
Can I make it as a beacon kit?
what changes do I need to do to change that as a Beacon? any Source and Instructions are very helpful for me....
We need our PCB assembler to be able to program nrf51822 modules in situ. We have tracked the PCB to include a tag-connect footprint to this end. The assembly house will purchase...
Dear all,
I have an issue using USB bootloader for NRF24LU1+ device.
I've used a USB dongle and programmed USB bootloader to chip via SPI using external programmer.
...
Hello guys,
I have tried to get Nordic-Thingy52-mesh-demo working, but now I don't see it works according to description done.
I have followed all steps provided on...
Hi,
we are developing against the nRF52840 chip. We are interpreting the documentation as indicating that each pin can do all of GPIO, PWM, I2C and SPI. Are we reading this...
Hello,
I'm using SDK 15 and I just started to run the "ble_app_uart" example code. I'm hoping someone can help me find where the data sent from the nRF UART mobile app is...
I am using few keys that are 20 byte arrays, these are unique for each chip. Right now they are hardcoded. I don't want to recompile for each device. I want to write to these...
