Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
There are 12 LEDs which are connected using shift register HC595 ,the module used is nrf51822(bluetooth module). I want the LEDs to go off after 3 seconds interval. My code...
Hi there,
We are having issues with our boards that uses nrf52832 chip. Our first built had this chip and everything was working fine. We built a second batch and all boards...
Hi,
In nRF52832 datasheet I found that it is having internal oscillators, like 32.768Khz RC oscillator and 64MHz RC oscillator. If it is having internal oscillators what...
Hello
Most of the time we shall use the BT TX 0dBm. In special cases when we want to increase the communication distance we may select the 8dBm mode.
For RF type approval...
I am implementing long read with authorization in the server (peripheral). I have a characteristic with vlen = 1 and maxlen = 300. ATT_MTU = 23.
gatts_attr_md.vlen = true;...
Hi,
I added nRF5_SDK_15.2.0_9412b96\modules\nrfx\drivers\src\nrfx_timer.c to my project. In sdk_config.h I have:
#define NRFX_TIMER_ENABLED 1 #define NRFX_TIMER1_ENABLED...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96,PC is windows 10
I want to use the DFU to update my file,but I find that only the Init packet is signatured...
I am trying to integrate SPS30 sensor to nRF52 DK using Segger Embedded Studio. The sensor fails to initialise and the program keeps getting stuck at NRF_BREAKPOINT_COND at...
Hi,
In nRF24 / nRF51 , the product sheet have the 20dB Bandwidth for Modulated Carrier (2Mbps) parameter.
However , i could not find at nRF52832 ps.
Did it the same...
Before updating firmware i have updated connection parameter with low connection interval. But it taking too much time. If I gave the same parameters at the first time while...
Dear sir.
This is jaykim from south KOREA.
I saw your company website about NRF2460 Chip.
Is this chip discontinue? It means not product any more??
Because We now...
Hei hi.
I'm developing simple beacon application with sdk 15.2, sd132 based on freeRTOS on nrf52832. The app and the whole project is built with help of ble_peripheral/ble_app_hrs_freertos...
void spi_read_write(0x1E,0x00) ==> output 0x10 as return value of register read.
Here I want to send value 0x90 as register value in the argument of spi_read_write(0x1E...
Hello, Looking for help in confirming what happens when pin 0.21 is grounded on the 810. I have a simple custom 810 based on the reference design with an added led and rgb...
