Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
hello everybody!
i want to sample an analog signal with the board and send the 0/1 data with ble to the receiver .
i created my on service with rx and tx like in ble uart...
Hello Nordic Expert,
I am facing a stall pid issue with nRF52840 Dongle using nRF5_SDK_15.2.0_9412b96. The chip build code is QIAA C0 . I started with usbd_hid_generic example...
I have an application with Nordic devices as Central and Peripheral.
The first device is a multi-protocol device (nRF52840) and acts as BLE peripheral. Min connection interval...
Hello
System:
OS: Windows 10 x64
Application: nRF Connect 2.6.1 (with Bluetooth Low Energy 2.2.0 and Programmer 1.0.2)
Problem:
My device is connected to the COM7...
Hi,
I currently have a custom board with an nRF51422 on board. I am considering upgrading to the nRF52 series. Are there any nRF52 models that are pin compatible that I...
Hello,
We are working on a network of low energy sensors that work without connection. The sensors have a configurable service, so from time to time it makes itself available...
Hi,
I'm trying to implement Buttonless DFU into an existing BLE application. I'm using nRF52832 V1.1.0 boards (one for the BLE peripheral running the application and buttonless...
currently i am running ble_app_uart_c example from sdk15.0 and i successfully discover one of the custom service.now i want to discover all the services provided by peripheral...
What is the output for the capacitive sense driver example? ADC code? Voltage? Time? For example, when the csense_handler function is called, the following line will print...
Hi I'm facing problem to detect external crystal oscillator in my custom nrf52832 board's. I'm think it is not connection issue as I'm facing same issue in other 9 boards...
Hello, everybody.
I'm working on combining the nRF52840 and the GPS module and are currently developing a program that stores real-time GPS data in an external flash memory...
Hi,
We are planning on upgrading the firmware on our device from Mesh v0.9.2 to Mesh v3.0.0 via BLE.
Specifically, our current stack uses: - nRF5 SDK for Mesh v0.9.2 ...
IPhoneX sometimes goes into the ble_evt_handler auth_status event, and then p_ble_evt->evt.gap_evt.params. Auth_status.auth_status!= BLE_GAP_SEC_STATUS_SUCCESS, other iPhone...
I am unable to compile any SDK12 example with SES even following the tutorials. Versions in tutorials are different from those actually available resulting that menus shown...
