When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
At the top of the Nordic home page, there's a link for "Bluetooth Software":
Following that takes us to https://www.nordicsemi.com/Software-and-Tools/Software/Bluetooth...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
Hi,
I am facing problem while developing code for the application.
I am working on the "ble_app_uart" example code to develop my one of the application, But after making...
I'm using the code from Vidar supplied here . It works well, but shuts off after 3 minutes.
Based on the idle_state_handle brief, " If there is no pending log operation...
Hello,
I would like to touch on some problem we encountered when using the MPU9250 sensor.
Our goal in the project is to simulate the movements of the MPU9250 sensor in...
When I use the nRF connect app on android phones, the services and characteristics can be detected and controlled correctly, as below.
But when I switch to iOS nRF Connect...
I am using the nRF5_SDK_15.2.0_9412b96 for development of nRF52840. I have both the nRF52840 dongle and also the DK.
I find that I am not able to change the default Nordic...
Hello. I have build by application on nRF52832 based on ble_app_template example (SDK 15.1, softdevce s132 6.1.0). I've configurated Peer Manager library as it recommended...
i use nrf_drv_twi_init(&m_pedo_twi, &twi_pedo_config, ai_pedo_twi_handler, NULL) open I2C , sent data , then use nrf_drv_twi_uninit(&m_pedo_twi) close i2c, but power consumption...
I want to use nrf52832 SPIM， In nRF52832_PS_V1.4 it described that "An SPI master transaction is started by triggering the START task.Following a START task, the SPI master...
