Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
Hi guys
I am planning to develop a beacon app, but I am not sure what would be the minimum scanning interval in order to keep the phone's battery drain on a fairly good...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
Hi, there! nRf Toolbox drove me crazy!! can anyone help me?
I flash "s130_nrf51_2.0.0_softdevice.hex" to the pca10028 board.
I compile the bootloader example "nRF5_SDK_11...
Hi,
I'am having an issue with UART using app_uart_fifo.c (SDK 0.9.2). At times I get communication error (usually at attaching and detaching uart connector) and my error...
Hi.
I'm little worried about our bt sensor power consumption.
We are using twi/i2c to communicate with sensors periodically. We are using app timer to trigger these...
I have a custom board that doesn't use the external 32Khz crystal. The engineer that designed it chose to use P0.0 as UART RX. (I know, poor choice.) I have set up a custom_board...
I am using SDK_11 s130. I see APP_ERROR_CHECK(err_code) being used throughout the SDK examples. When err_code is any value other than NRF_SUCCESS, the nRF51-dk board will...
Previously, I was able to program ble_app_uart using SDK_11 s130 into nRF51-dk. Now, I would like to program ble_app_uart into Adafruit Bluefruit LE friend board. www.adafruit...
I have been following the advertising tutorial and decided to start my own application using nordics git repo as a reference. After a few debug sessions I found that I needed...
I am trying to probe sysclk signal on one of the unused GPIO pins on a nRF52 board. I modified the ble_app_template example provided in SDK 11.0.0 and added a sysclk function...
I am trying to connect nRF52 with 7120 and create a NFC card reader , is this a solution and power efficient solution .
I will interface through I2C , is there a example...
I am using the sdk version 11 and arm-none-eabi-gcc version 5.4 on linux mint to compile the blinky test application. I have pointed the Makefile-posix at the location of...
I am doing the test about timeslot with the project link text
but it cannot scaninng and i found the timeslot is work because i get event NRF_EVT_RADIO_BLOCKED and it call...
Hello,
my application has to emit measurements in the manufacturer specific data structure continuously and has to accept a connection, for example for ANCS. Therefore...
