Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello，
As I was using the sample“nrf_dm”（SDK v2.6.1),I wondered how programs were run, how threads were scheduled to give measurements, and how I could learn about this...
Hi, I'm working on nRF5340, NCS v2.6.1, Zephyr v3.4.99. The net core is running the child image HCI RPMsg controller. Th app core is running application and child image mcuboot...
Using the following code block nRF52833(PRX) can receive the data from PTX(nRF24L01+).
But how nRF52833 replies to nRF24L01+ with the ACK packet which includes user...
Hi, in order to reuse the original factory public Bluetooth MAC of nRF5340 based radio module, I had introduced a function that reads the MAC address out of UICR.OTP area...
After enabling Littlefs, I wanted to use a serial port to write files to it. I first tried using mcumgr, but currently encountered some problems. So, I tried to directly read...
Hi all,
I am using nrf SDK v2.5.2 and zephyr. In my application I want to measure a signal frequency coming from a GPIO, I read about the PPI and I thought it was good...
Hey there,
I'm trying to build the `hw_unique_key` sample for a nrf5340dk_app (non NS) with CONFIG_SECURE_BOOT so that its `child_image/b0.conf` with CONFIG_HW_UNIQUE_KEY_LOAD...
Hi,
I used to use the nRF51 with Keil, so not too much experience with new SDK, but I have followed the "nRF connect SDK fundamentals" and "BLE fundamentals".
I am trying...
I downloaded the report from the official website in August 2023, but the client has given feedback that it has expired and they need the most recent one.
I would like to test GPIOE APIs on nRF5340 develop board. But west build generated the following warning message.
Could I use nrfx_gpiote _xxx related APIs ( infocenter...
hi
I am trying to get the nrf7002 dk working, however, when i try to provision the kit using the nrf wifi provisioner app i get an error saying " scanning error received...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...
Hello,
With the latest version of the nRF5340 MDK I am getting the following linker errors (below), and don't understand why they should turning up.
Best regards
==...
I need to use ADC in the project, and then I have configured ADC in overlay. The code is as follows
The same code can be measured normally in Zephyr's ADC example, but...
