Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi Nordic Team,
My dev enviroment is as follow:
nRF52832(ble central)+ S132+ SES+ SDK 17.0
We are facing an issue regarding local BLE Address . When we are flashing...
Hello.
I am developing a peripheral roll using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to know the information of the device that sent the connection request. Also...
Dear Nordic Team Support,
I am testing throughput on different environments, my goal is to stream data from custom-board to Laptop. I have set up some experiments as shown...
Hi all:
I am using nrf52840 hardware. nrf connect sdk.
I am using file system and mcuboot at the same time. When i call ` flash_area_open (id, & pfa);`, i got a wrong...
Hello,
we developed a proprietary protocol on top of IEEE 802.15.4 user zephyr on a nRF52833. Everything was fine with hal_nordic on commit 74b3b21f60aa3dc9a4364ffc28dbb47ad8b699a9...
When I pair the peripheral with a dongle connected to nRF Connect Desktop application, then disconnect and Connect again, the nRF Connect does not remember that it was paired...
I built the SMS sample without changing anything. I am using a Lebara prepaid sim card. I was able to exchange SMS messages from one cellular phone to another. I checked with...
Hello,
For a long range test between the nRF Toolbox Android app and the ble_app_hrs (in nRF5_SDK_17.1.0 package) over the nRF52840-DK. I would need to setup this board...
Hi,
I initiated pin 28 as SCK of SPI as normal condition, and I'd like to switch pin 28 as GPIOTE while receiving a command via BLE.
Basically this is how I achieve...
Hi,
I have loaded a simple application on my nRF52840 that just activates a GPIO as soon as it reaches the main loop.
The SoC is powered externally according to the chapter...
Hi,
We will create a ble peripheral device and also can handle timing-critical uart request. The uart will be always communicating and response time can't be slower than...
Dear DevZone:
I am developing an evaluation board with the nRF9160 SiP model, but I have some doubts with the software. Does nRF9160 SiP come factory preloaded with any...
Hi,
I try to implement Serial DFU update using the info in the " Add DFU support to your application " at link
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hi Team,
When the slave side of the SPI received data from the master side, I want to log the received data to judge If it is right. But, I want to print it by log. it can...
