I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
in prj.conf, i add below:
CONFIG_BT_USER_DATA_LEN_UPDATE=y CONFIG_BT_CTLR_TX_BUFFER_SIZE=251 CONFIG_BT_CTLR_DATA_LENGTH_MAX=251
in att_internal.h , change # define BT_ATT_DEFAULT_LE_MTU...
Hi!
I wonder how can I measure the delays, latency, errors and connection speeds. I'm using nrf samples for bluetooth peripheral_uart connect it with nrf connect app. I...
I have a SPI Master and a SPI Slave. The Master will randomly pull data over SPI from the Slave. The slave will randomly generate events that result in data to be sent to...
I am using SDK version 17.0.2. The example code uses SPI.
The following changes have been made to the pin settings.
Questions
1. Pin behavior is strange.
...
Hello, Support team.
Our boards do SPI communication to read sensor data.
Basically It works well. I checked that It operates more than 5 hours.
But only one board...
Hi,
I have the following initialization for advertising:
The name consists of an acronym od three letters and a underscore e,g, XXX_ and a six digit ID. Like XXX_12E124...
Hi,
Is it possible to add four pairs of resistors between the debug signal lines and the connector as shown in the figure below.
Would such a connection not impair the...
The Google Fast Pair Service has recently been included in a number of Bluetooth peripherals (Headphones, fitness trackers, etc.) and has been getting rave reviews.
Has...
I am able to download simple blinky program on my custom board. It is working fine. Custom board is interfaced with nRF52-DK through P19. I am using embedded studio as IDE...
Hi, on nRF5340 I want to capture accurate timing of external events. I need a kind of real-time capture module to read the time period of a pulse train generated by a rotating...
Have a few questions about ble_app_uart example.
From the way I see it, it sets uart_event_handle as the callback, and every time there's an "event" that takes place...
Hello All,
Method 1: I am writing a test application to read the ADC data at a specific intervals(10 samples for every 5ms interval for every 50sec). I am using blocking...
Hi,
We are implementing a synchronous light flashing of multiple devices, so:
1) Can we get a millisecond level (< 10ms) time synchronization by parsing the Link Layer...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
