I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
Hi all!
I'm trying to run the BLE light switch example on the nRF52833 development board using Segger. I get the following error whenever I try to build the client. This...
sorry where i can find the document/spec for the API that we can use to comunicate with LTE stack L3 . Using Zephyr ? threre are some examples that can help me ?
Best Regards...
Hello everybody, I have to develop an embedded system to acquire and process data. I will be using 2 custom PCBs based on nRF52832: 1- Sensor board: very low power consumption...
Hi Nordic, Please, I am doing a design with nRF52840 and would like to be clear on a few points. Attached is the electrical diagram .
Point 1 For the power supply I am using...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Given a 3rd party BLE device (for example a fitness) watch, would it be possible to connect to it using the nRF52 DK and conduct a DFU on it? If so, is there any documentation...
Hi,
I am trying to nrfutil to execute dfu over BLE using nrf52 dk and nrfutil. I have no problems when I try to use nrf_connect mobile app, but I want to use nrfutil desktop...
I want to write my application logs to the flash. I am following this tutorial which is for nrf52: https://jimmywongiot.com/2020/02/24/print-log-flash-log-crash-log-on-nordic...
I want to change the GPIO settings for the pin P1.08 but in the register description (nRF52840_PS_v1.2.pdf) there are only the names and offsets for the pins from P0.00 to...
I've been looking for a DC Motor controller example (for nRF52840) but without luck. Some other users have referred to such an example so I figured it should exist.
Anyone...
I am using SPIM4 with easyDMA in list mode to read a set of registers from an SPI device, and everything seemed to work great until I attempted to use the double buffered...
For some reason I can no longer compile any Zigbee examples.
The errors I am getting are below.
I have no idea what the issue is and I can't find any resources to help...
Dear sirs,
Here we've faced with the issue about logs output, could you please help?
We need to use two CDC_ACM devices on the board: one for shell and printk() output...
