Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi ,
I want to compile mesh examples .I tried it using segger ide Alternatively,I wish to compile it in cmake too. Can you please tell me the procedure to compile code using...
Hi,
I was able the configure the sample to connect to AWS but I cannot figure out where the cloud_send function is sending the data. Is there any documentation on where...
Hi all,
I am using a nRF52840-DK as SPI slave with a MSP430 as host SPI master for a nRF8001 replacement application.
As I am absolutely not familiar with high level functions...
I am trying to communicate with a SH1106 OLED display using TWI and the popular u8g2 display controller library.
I've verified that the display works without problems on...
I am currently development an app based on the example from the experimental folder using a NRF DK52 as a relay between a central and multiple peripherals.
The app should...
Hello,
Happy New Year.
I'm not able to find nRF52840-QIAA-T or any replacement of this SoC available in the North American market.
I need atleast 5 SoC of the...
Setup: nrf52840 (without internal dc/dc), VDD = 3.3V
Assuming the VDD rail ramps up slowly, the nrf52 will start booting at it's power-on reset threshold of 1.75V (POR)...
Dear BLE Experts, I've followed this tutorial to create a custom GATT service and characteristic. The tutorial seems to be based on the BLE SDK , not the MESH sdk, hence the...
Hello,
Our company is kicking off a project (while we are at the very beginning stage) where multiple nodes (up to 1K) should be connected within a mutual network. I wanted...
We are looking to increase battery life for a product that uses the nRF52832. I'm wondering if it's possible to provide 1.3V directly to the DEC4 pin rather than use the internal...
Hi, I'm referring to this post over 3 years ago: Nordic DevZone (nordicsemi.com)
I'm using Android 8.0, and I'm using SDK 12.3.0 for firmware. I'm trying to create bond...
Hi,
I noticed that when I initiate a chip-erase on the flash-chip and reset the MCU, I'm getting NRFX_ERROR_TIMEOUT's on my nrfx_qspi_init().
I found this ticket: https...
i am using nrf52840 DK with softdevice (s140_nrf52840_5.0.0-1.alpha_softdevice) and applying this throughput example ATT_MTU Throughput Example . and notice that when I use...
Hello I have a problem with the scanning of ble phy coded in Android, I need it to be continuous (or almost) but it seems that for coded it is not possible unlike with legacy...
