Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I'm trying to implement the NRF5340 as an I2C slave. The current answers all show the answer as old to look for a newer answer. Were implementing the NRF5340 as a slave to...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
I am currently working with the Aliro 1.0.0 from nRF Door Lock and Access Control Add-on.
I need to know how to properly configure or set custom data fields for Aliro protocol...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
I am attempting to get familiar with the NDEF support on the nRF54L15 DK. After creating a copy of a sample based on the WRITABLE_NDEF_MSG example, I create a build configuration...
Hello Nordic Support Team, I am developing BLE content, where nodes will be periodically uploaded to the gateway.During this interval,the CPU needs to be kept idle, waiting...
Hello DevZone,
I have wrote a standard Zephyr display driver for one customer, I used sQSPI and Zephyr MSPI API.
I finished the development, but the QSPI (1-1-4 mode)...
Hello,
Our product (sports timing) will be used at the upcoming Olympics and our customer is being asked some questions about wireless specs. We use Bluetooth 5 (backward...
Hi,
I have a custom nRF52832 PCB with 10 buttons connected to various GPIOs. All buttons work correctly except the two connected to P0.07 and P0.08 they produce no response...
Hi,
“ We are designing our board with the nRF54LM20, and both the SPI/QSPI and UART peripherals can operate independently and be mapped to separate GPIOs.in QFN-52 Package...
I am working with the DTM sample on nRF52840 using nRF Connect SDK (Zephyr) .
My goal is to run a continuous TX test automatically at boot (standalone) , without requiring...
My Setup and Environment We have built a custom PCB with an nRF5340 and an nRF7002Q Wi-Fi module. I have attached the relevant schematics for the PCB.
We are using the nRF...
HI
I'm having an issue where VS Code cannot recognize the SDK and toolchain. Everything was working fine before, but now errors occur when I open VS Code and try to build...
