Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello, I wanted to send data over peripheral device to the central device by using ble UART example. I used ble_nus_data_send() function in main(void) function. I have checked...
Hi, New user here, I develop using Kicad and it has an antenna based on the Ti SWRA117D design, which is 2.4GHz. Can I confirm I only need two components (as per reference...
Hello,
I am using the SPIM module to communicate the NRF52832 with a sensor, every time it generates an interrupt - which is generated with a frequency of 25Hz. For the...
Hi expert,
I'm working for my project that make a controller for drone, and that i need nus for as my service so i can exchange the data (send order via rx from smartphone...
Hi I'm trying to integrate the iBeacon and Eddystone protocol together. For this I'm using the timeslot to advertise the packets simultaneously. I have successfully integrated...
Hi,
I currently did many test with BLE our new devices, and i am stuck on this probleme since days. The goal of those test are to have internal too for validation process...
I am working on my first nRF52832 design utilizing a 4 layer PCB. I have been reviewing the different antenna options for this device and have some questions about the PCB...
Hi Everyone I am trying to get a hold of the nrf9160 SDK which is based on zephyr. Here is what i would like to know 1. There is a file named zephyr.dts which has all the...
Hey guys, I've been trying to do a range test with 2x PCA10056 dev kits. I believe I've set everything up correctly and cannot achieve more than 300-400 meters before the...
If we input 5V DC supply to Vin 3-5V P20, the Bluetooth programming failed at start. But if we input 3.3V DC supply to P21, the Bluetooth programming passed. Is this Vin 3...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
It seems that the route is decided by the leader, can I specify the route?
...
I am making a simple breakout board for the nRF52833 (I'm using Fanstel's BM833 module). This is what my board is looking like. There's a ground plain on the top and the bottom...
I'm trying to send data from a NUCLEO F401RE board with the nRF 52840 DK using UART. Then have the data to be sent to my phone via Bluetooth. I'm starting from the ble_app_uart...
Hi Devzone:
I have a question that may be common for companies distributing hardware containing nrf52840 chips.
I have figured out how to use nrfutil to generate Bootloader...
