Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I am setting up a custom hid device bulk transmission, which can normally send data to PC at present, but cannot receive data from PC (no data interrupt was received in the...
I am able to use the 2 channel mode of each PWM giving me a total of six PWM that I can set individual duty cycle PWM!
I now find I need 8 PWM with individual duty cycles...
I see that BBC Micro:bit uses nrf51822 and can use RADIO peripheral.
So I tried to make my nrf52832 DK to talk to Micro:bit by using Gazell library and referencing MicroBitRadio...
Hi,
We are using SDK14.2.0 and getting assertion failed error with id = 1, pc = 0xEAC2 and info = 0.
What can be the cause of this error?
Thank you in advanced.
The function model_timer_elapsed_ticks_get() returns the total number of ticks since the timer was started. Hence it's expected that this function to return a value > 0 when...
I am attempting to do the LTE_Gateway example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for the...
Dear All,
I am using NRF52840 DK with SDK13.0 . I am trying to use one SAADC channel (CH 1) to record input signals at 200 kHz to fill a buffer of 2000 points . After the...
Hi
I was playing around with the new SDK 15.3.0 and most things worked as expected. One thing that causes some trouble is the changed MBR parameter page handling. It seems...
i need to generate an irk from nrf52 so that no device can identify that nrf52 data...only the device with same irk can identify and connect to it
for that what should i...
I am trying to port Keil code to SES 3.40 with NRF51822 Device and SDKV12_3, I am currently using the ble_app_uart example. I followed this blog post https://devzone.nordicsemi...
Hi Sir
Is it possible write a hex file to external QSPI flash by nrfjprog ? if yes, please tell me what's the command ? Thank you.
ps, the hex file is data, not firmware...
We are using nRF52840 SDK 15.0 with Segger embedded studio. We have referred ble_app_proximity example only for read battery level using ADC. Now in our application used SAADC...
Hi, I m using nrf 51822 development board. I want to implement timer in input mode to detect falling edge of the pulse.. It should give intrude when any falling edge is detected...
Hello
I am a big fan of Zephyr OS, and have developed several commercial products with it (on other NRF chips)
I would like to know if the nrf9160 is to be supported...
Hello, I would like some guidance on how to create a standalone executable for nrfutil (like nrfutil.exe on Windows) in order to update my hardware through OSX. Very newbie...
