Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello to everyone.
I´m trying to understand a code starting from the file of definition of pins of nRF52 PCA10040. In "simple_hal.c" there's a line like this: NRF_GPIO-...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
Hi,
My system needs to maintain certain gpio at their state at all times, including when switching to bootloader,
I understand that reset will also return my gpios to...
I'm trying to set up an ESB PRX on an nRF52 that has to communicate with an nRF24L01 chip acting as PTX. Because I want to react to the received data as quickly as possible...
Hello,
I am trying to use Softdevice and the latest Github version of 802.15.4 support. The make (using linux/armgcc) fails on
nrf_raal_softdevice.c
because nrf_802154_radio_irq_handler...
Using SDK 15.2 on an nRF52832 using SoftDevice S132. FDS works OK unless the SoftDevice is enabled. None of the examples work. We've tried the peripheral example, GitHub examples...
Hi,
I'am testing direct advertise and I found strange behaviour with "nrf connect" app.
1. Direct advertises won't be proceeded on "nrf connect" unless there is at least...
Hello everyone
I got back on my bluetooth mesh project after an interruption and at the time I remember having the same compilation problems solved so far.
I worked with...
Hi all,
I acquired the wonderful nRF9160 DevKit which embeds the ARM CryptoCell 310.
Rather than using the mbedTLS or TinyCrypt libs, I would like to rely on the CC310...
hi....
i am just started to program the mesh , i am getting the error in my example code , how to solve ? this is the latest version of 3.1
boards.h: No such file or ...
Hi,
I am using 15.2.0 SDK and 3.0.0 Mesh SDK for developing the nRF Mesh.
I am using segger IDE for programming but I am looking for a way to program the device with hex...
Hi
In MESH 3.10 SDK，i want to configure and use virtual address, but i can't add the virtual address in both pulication address/subscription address when i use NRF Mesh...
