I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
LED is on when the button is pressed. Press the button again and the LED off. I want the Turn the LED on as long as I press the button. Turn off the LED when I stop...
Hi there,
I've already implemented a custom firmware for nRF52832 with SDK 15.0.0 and S132 v6.0.0 which uses both advertising and scan operations, and now I'd like to use...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I'm wondering why the pairing request sometimes shows up in the notification bar and...
Hi,
I am using nRF52832 with sdk 15, freertos.
I need to implement the following logic:
1. Get into low power mode, while keeping a timer running.
2. Every 10 mins...
I was using NRF52832 and s132 v6.0.
I have Android phone's IRK and I have added the Android phone into the identites list manually.
After doing the direct advertising...
In the NRF52-DK user guide, the following is stated:
Important: When using ANT/ANT+, the 32.768 kHz crystal (X2) is required for correct operation.
However, I could...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
Hello,
BLE MESH 3.0 Light Sw Example code just I have add APP_TIMER_MODE_REPEATED and its work fine.
Case 1:if I print string Or LED Toggle Based on timer its working...
Hei there!
First of all thanks for all the great work here!
My question is:
In my application, the final device will have 4 pogo pins.
Two of them are for power, the...
Hello All,
Hello all,
I am working on BT832A in which nRF52810 is used and i used segger studio for programming in windows 7. I am refer nRF52 SDK 15.2.0. And i am load...
In the manual for the nRF5284 there is a listing for some divider settings for the MCKFREQ. The size of the register and the values to set indicates that there are a much...
Hi
working on a NRF51822 device with SDK12
I was using nrfjprog version: 9.7.1 to create a setting.hex with the following line
nrfutil settings generate --family...
i am using this project:
\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c\main.c as center.
nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\main...
