I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi,
I just want to verify-
The MAC address of the bootloader is the app MAC address +1, assuming we are using the default configuration.
Is that correct?
Thanks, ...
Hi Support team,
The Online Power Profiler is calculating the Average Current consumption for nRF52840 DK board in a wrong way.
Calculation is of blocks. => Pre-processing...
Hello
I would like to integrate DFU into my application
but, when including:
#ifdef BLE_DFU_APP_SUPPORT #include "ble_dfu.h" #include "dfu_app_handler.h" #endif...
Dear NRF Team:
I successfully updated the firmware (blinky_nrf52840_xxAA_s140_6.1.0) according to the Mesh DFU steps.
However, the second DFU cannot be performed after...
I am experiencing an issue where the program hangs on one board, but not another. I am able to program the Evaluation board (EV BT832AF) ok and run everything, but when I...
Hello,
I was wondering if it is possible to change some of the BLE Stack Configurations based on the number of devices connected...
e.g. Changing Connection Interval and...
Hi,
I am evaluating the Firmware on this github repo and my nrf52832.
At the moment I am compiling it using my makefile, however I would like to import this project...
Hi All.
We have flashed the hex-file of ble_app_blinky for pca10040 on the debugger, and things work fine.
We are using sdk-15.2 with softdevice-6.1.1
So, a question...
Hi there, I am having issues knowing how to get access to data coming through a VisualGDB embedded (C) project using the pc-ble-driver. I have my project working fine and...
Hi ,
Nrf52840.SDK15.2,Windows,Ses
Compile "secure_bootloader_usb_mbr_pca10056_debug " project, An error occurred. As follow：
Cannot open file: E:/new/project/wireless...
I have used the UART example up and got it working. So i can send and receive data using it.
However i wanted to modify it so as to run with the current RTOS environment...
Hello
According to BLE Specifications we should be able to get 125kbits/s over the air transmission i cannot seem to get anything remotely close to this.
Is there something...
I use Multilink and Blinky Demo with PCA10056 and PCA 10040 Board,when the two board close to each other there is no packet loss,but when i dispath each other with 50cm,there...
Hi,
I am currently using two different programmers(nrf51DK, Segger flasher portable plus), programming software's ( NRFgo Studio, Jflash). Here are my issues:
When I...
Got this error while trying to perform a DFU over BLE (noble) on a raspberry pi 3. The peripheral should be running v15.
Here is the partial log just before the error...
