Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I am trying to connect nrf52832 with custom android app, after connection established beacon sends message. Sometimes I can establish the connection after 8 tries, sometimes...
Hi,
I'm working on a project which uses two nRF51822 (SD130 and SDK v11.0) on mobile devices. Device A is continously advertising and device B scans for a fixed interval...
I'm looking to sync an ADC reading with the PWM output. I'm using PPI for this but fails to make it synchronise properly with the PWM.
I'm getting interrupts and sampled...
Hello,i am using nrfsdk with softdevice 6.0.0 in my application and by using it i am trying to connect my mobile uart application with my BLE .but i am facing some issues...
Hallo all
I have an appliation using the LOG for TX output to uart,
I want to maintain this code but to add RX based on the app_fifo_init,
how can they coexist ?
thanks...
Hi,
I would like to use the nrf52 as my bluetooth end device, which inturn has to communicate with the Bluetooth IOT gateway like Rigado module or Nordic gateway APP(which...
Hi
I am using SDK 14.0.0 and soft device S130.
I am planning to add SPI functionality to BLE's sample code.
However, when moving to the next instruction after SPI data...
I am developing a beacon using nrf52810. This beacon will advertise iBeacon as well as Eddystone packets. And user should be able to configure some of the beacon paramters...
Hi Nordic,
I am using the example nrf_app_interactive with nrf52 DK. I am using it as a central while connecting to a peripheral. This peripheral has a lot custom services...
Hi,
I need implement a single Byte transaction on SPIM.
I implemented a stop as documented in
setup_workaround_for_ftpan_58 function
It works only for the first...
I want to use the RTC Tick Event as my system tick. But on both the RTC0 and RTC1 my programm freezes after about 8min.
It looks like the Tick interrupt is still served...
Hi,
We are currently at the process of manufacturing prototype boards, the manufacture cannot do pitch size under 0.25mm. They kept telling us that the chip's BGAs exceed...
Hi, I got a nrf51822 board and a st link v2 mini as shown below. I have been trying to connect the nrf51822 board so that i can upload code to the board by following this...
Hello folks,
I'm newbie on NRF, I have NRF51422 with Keil IDE and I want to create a mesh network on that kit which will continuously broadcast the data of sensors to the...
