When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi,
I've made a customized version of the nrf_desktop desktop mouse build and I ported it to work on a custom nRF52833 board. I've been using Segger Embedded Studio to debug...
Hi,
I am following example to connect using TLS. I am not polling, as in the example. Should I expect that after
mqtt_connect, to be called in the callback?
mqtt_connect...
I am encountering an MPSL ASSERT: 106, 501 error followed by a HARD FAULT while running my distance measurement example on an nRF52840 using the nRF Connect SDK v2.5.1. The...
in Bluetooth Low Energy Fundamentals -> lesson 3-> Exercise 2 I opened the solution, I built the config for nrf52840 dev kit. Problem: 2M PHY is not achieved. Update to 2M...
Hi I am a student exploring on the usage of nRF52840 utilsing Thread communication protocol but i cant seems to get it setup for the configuration. The documentation is quite...
Hi,
I've been using the nRF5 SDK (17.1.0) USB Mass storage code for a data logger I have made. I am using a memory chip larger than 16KB and that code has bugs when you...
Hello,
I am currently using the nrf52840 evaluation board in developing a prototype. Once this goes into production, what are my options for programming the firmware? What...
When using l2cap to stream data at a high rate from device to an app we are seeing a hard fault in l2cap_data_pull when there is queued l2cap send data.
When the fault...
Hi,
I encountered a stop scanning issue when running the nrf5340_audio application without any configuration changes .
The only modification I made was changing the log...
I am building a firmware based on nRF Desktop, but can reproduce the issue in nRF Desktop SDK 2.9.0. The issue is that MCUBoot takes almost 1s to start the app, even with...
I'm using the visual studio code extension and things work well. I am now trying to test a more complex project found here but when pressing build I get some very long errors...
I am currently working on a distance measurement library using the nRF52840 DK and nRF52840 dongle. I have successfully obtained distance values on the serial terminal, but...
Evaluating direct access I2C operation with the NRF9160DK. I have a INA219 connected to pin 30 & pin 31. I am aware that there is a zephyr driver for the INA219, but I want...
Hello all,
Going through the nRF Connect SDK Intermediate course with my nRF54L15 DK, I stumbled upon a problem at step 6 of exercise 3 - Interfacing with ADC using nrfx...
NCS 2.6.0, sysbuild with mcuboot
nrf52840
I'm trying to add LED indication during mcuboot image transfer. Currently it takes 20-30 seconds for the image copy and the...
