Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
ble_dtm.c has some bugs related to signed integer representation which prevent negative power (less than 0 dBm) from being requested in the vendor specific message.
...
Hi, all.
I'm using "SEGGER_RTT_printf" for debugging. Because have no uart port on my development board.
I want print double type variable like below.
double pi...
I am currently trying to communicate with a GPS module using the UART on an nRF51422 (using the Dynastream N548M5CB module). I am using SDK v9.0.0 and the FIFO version of...
Hi,
I want to send a continuous stream of data very quickly into the nRF51 through SPI and then dispatching it to a smartphone via BLE.
However I keep getting BLE no...
Hello
When i am in keil uvision 5.18 and use the pack installer all the examples using Softdevice S110 are gone in Keil. Is this a known issue and is there any way to solve...
I followed the instructions and comments in devzone.nordicsemi.com/.../ . I built a project around the ble_app_gls example (with a couple of minor changes such as using -DNRF_LOG_USES_RTT...
Hi, I would like to program nRF51822 flash over SWD interface. I have another micro LPC1100 series that has the flash image for RF51822 and connected to nRF51822 over SWDIO...
Hi,
It is written in the nf_drv_uart.h file for nrf_drv_uart_rx_abort() that
If Easy DMA is not used event will be
called from the function context. If
Easy DMA...
Dear All,
We work on the NRF52 CSP revB. We have a board with two external crystals (32MhZ and 32kHz).
When we use the example program with BLE and UART, it works great...
Hi,
How can i get time stamp from RTC1 timer? While i am using app_timer + Softdevice?
Or any other way
Thanks and Regards,just to get timestamps from timer?
Faizan...
Hi,
I added DFU function to the example of ble_app_hids_keyboard according to ble_app_hrs_dfu.uvproj.
Test environment: nrf51822_xxAA, SDK_v6_1_0 and S110_v7_1, before...
Hi all,
I would like to use Pstorage module. Since flash endurance is 20.000 write/erase cycle, I need to use it very efficiently. If I use pstorage_update function it...
Hello,
I am quite new to Beacon development. I am trying to use the examples of NRF SDK 10.0 on the NRF Beacon. I would like to "install" the application via OTA. I tried...
Hello,
DFU tool (android) is cool but if you have a lot of devices to update it's long. Is there any batch tool that can update all devices that fit (MAC list or SSID filter...
