I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
Nordic,
I am using the BLE Shield v2 and the Arduino Due board to transmit accelerometer/gyro data to an Android tablet app that plots this data. I had this working fine...
First I noticed that nordic has already updated the andriod nrf toolbox app to use softdevice v7, which allows updating the softdevice, bootloader and application.
The...
Hello all,
I'm working on a library for NRF24L01+ and PIC micro.
Unfortunately there is something wrong. On the receiver side, the micro correctly detects that a packet...
Hi,
I am knew to BLE and I was able to ran succesfully the blinky project. Now when I load the soft device on and then try to download the hr example if says "Flash download...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi,
I develop an application with the nRF51822 circuit. It is detectable with my smartphone, but not with a computer that has a Bluetooth 2.1 device. Is it possible to...
In the comment of this post , Marc Nicholas wrote:
Doesn't that require SWO to be implemented? (Which is not on the Nordic part).
Is it true, that SWO isn't available...
In SDK 6.0 I find there is a project of ble_app_hids_keyboard_serialization.uvproj in nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
and it contain...
Hey there,
today I'd tested around with the Dfu service.
Peripheral is nRF51822 running Sdk 5.2.0 bootloader example (Softdevice 6)
Central is Android 4.3 running...
I am unclear whether the soft radio takes care of updating the attribute when a write event occurs. I can see in the example codes that the notification flag is handled by...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
