Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi,
I have been debugging with Serial LTE Modem(SLM) without an external flash .
I made the circuit of nRF9160 (SICA) without the external flash (MX25R6435F?) , I would...
Hi All,
I am using nRF Connect SDK v2.7 + VsCode + NRF5340 DK and trying to add and extend matter-light-bulb sample. With ' MA-onofflight ' when I try to compile the project...
Hi,
I am working on nrf52840DK with NCS v2.7.0. I want to send the data to the addressable led strip using the pwm interface.
I am using the NRF PWM driver ( nrfx_pwm...
Hi there
Does anybody now if there is a implementation / reference project / company which solves the firmware over the air update of several devices inside a OpenThread...
I am having nrf52833 module where I need to update the firmware via uart, I am using sdk_16 and I'm unable to find the PCA10010 for uart. Can anyone suggest me how to attempt...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
SDK v2.7.0 nRF5340-DK with nRF7002-EK Matter samples (e.g. light bulb) Extra CMake arguments: -DSHIELD=nrf7002ek Use sysbuild
Tested with v2.6.2 (no sysbuild), and it...
hello ,
some brief about my board it is nrf ble nrf52810 without crystal.
i am using segger debugger.
while doing step by step execution it come till line sd_softdevice_enable...
Hello！
I am using the development board of NRF5340DK, I found an external flash (MX25) on it, I want to know how to program the external flash through the onboard jlink...
Hi, our design makes use of nRF52840 MCU. Power is supplied to VDDH pin from a Li-Po battery which can range from 2.5V to 4.2V. Internal REG0 is used to regulate voltage down...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
Hello,
When I upload the Matter Weather Station application to my Nordic Thingy:53, I encounter a problem.
I am trying to use Google Home to read sensor data, such as...
Hello, I have a custom development board using the 52840 chip, with two LEDs and a serial port connected. It worked well when developing with nrf5 previously. Recently, when...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
While compiling the custom project in nrf vs code , I am getting the following error;
Configuring incomplete...
