I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello All,
I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup,
https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. We have a project using the nrf52840, which is sometimes used by carriers. I ported radio_test to...
Hi
I am using HCI Power Control sample to dynamically control TX power. I found that the TX side's connection RSSI and RX side's are diferent, at some point it even has...
Hello, I'm trying to follow this example (Serial DFU) , on a nRF52840 custom board, but I'm getting the following error:
I couldn't find any relevant information and also...
Hi,
I have recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. To begin, I used the "Hello World" sample code. While I was able to successfully build...
I have searched everywhere and can't find a working example that shows how to create a new BLE ID and save it to the setting s partition.
Please show me the configurations...
We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
I am incorporating the nrf52840 into a new design and it is my first time working with a Nordic product. I am looking to start with the SEGGER J-LINK EDU MINI due to it's...
Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
Hi,
I am debugging the zigbee functionality and would like to enable the zigbee log,already enabled log in prj.conf but no data coming out.What do I have to do to enable...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
hi Nordic teams:
we meet one serious issue about LSM6DSL FIFO reading, our product (host mcu is nrf52840) need to read lsm6dsl FIFO data periodically with one second interval...
We are cons id ering using a nRF9151 on our upcoming project and we want to use the A-GPS functionality via your Nordic Cloud and transmit this via CoAP. However some questions...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
