Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
I seemed to be randomly causing problems to our nRF52840 Zephyr v2.02 sensor's flash.
Previously I had bricked 3 sensors somehow. Before full production, I need to know...
Hello,
I want to implement a vendor-specific service on the nRF5340.
Is there any suitable sample code in NCS 2.2.0?
Or if there is any documentation I should refer...
Hi,
I have a nrf52820 on a pcb without 32Mhz crystal. I am using nrf52833DK to flash the nrf52820 on the pcb using debug out port on DK. I am able to see the connected device...
Hi, it's me, once again. Thankfully the last problem I had was actually my fault... I got distracted and didn't notice a small implementation detail... anyway... Here's today...
Hi,
The customer test routine serial_lte_modem mqtt returns 9,0
What does this state mean?
* ``9`` - Ping response from the MQTT broker.
Thank you for all your...
Hi,
I'm getting the following error during migration from 2.0.0 to 2.1.0:
[505/551] Building CXX object CMakeFiles/app.dir/C_/ncs/v2.1.0/modules/lib/matter/src/app/util...
Hi all.
I'm trying to learn a bit more about the device overlays,
I'd like to know how I would access the "gpio-line-names" that I've specified in my overlay in my application...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
Hello,
I am currently having my product, which is based on the nrf52810 SOC, tested and certified. I have been told to set my device up to use the DTM firmware example in...
Hello everyone
I have a few questions about how the nrf chip works: - does nrf52 work by sending AT comman and we need an intermediate chip like pca10040 send AT command...
I am trying to modify the Zigbee light switch example to transmit commands to the first bound endpoint, rather than to a bulb address determined by the app logic:
ZB_ZCL_ON_OFF_SEND_REQ...
Hi,
I am testing GPIOTE interrupts on 833, and noticed the interrupt is not fired sometimes (randomly) on power up. The input level did change as measured but the interrupt...
In this commit https://github.com/nrfconnect/sdk-zephyr/commit/d4023b3c1b8c32d978299143125ce5543c9bc6bb and this conflicting commit https://github.com/nrfconnect/sdk-zephyr...
Hello,
I am trying to compile the zephyr/samples/subsys/display/lvgl.
I have the lv_conf.h enabled
I'm getting an error "No SOURCES given to Zephyr library: drivers_display...
