Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi, I am new to Zephyr and Nrf, I am trying to replicate the event manager arch from asset tracker v2 but I am stuck in the setup. I am trying to use the logging capacities...
I am working on the Electronic Braille Display for visually challenged persons.
Our device will communicate with Voice over service on the laptops and smart phones using...
Hi,
with %SHORTSWVER: nrf9160_1.3.1 I am getting:
AT%CMNG=0,3,4,"test1234" OK
AT%CMNG=0,3,3,"30313233343536373839303030303030" OK
AT%CMNG=1 %CMNG: 0,6,"0606060606060606060606060606060606060606060606060606060606060606...
I have a single sample of the new nRF52840_XXAA at hand on our custom board. I'm trying to do a --recover with nrfjprog. As the log below shows, nrfjprog recognizes it as...
Hello ,
I m using SES v5.6 and NRF52805 ,ble_app_uart ex (nRF5_SDK_17.1.0),
Requirement -need to wake up and reset ( or start advertising again) from sleep mode ,when...
Hello,
I have adapted some of the ESB proprietary Protocol from the NRF SDK into my own project without installing the SDK directly; however, complete integration seems...
Hi Team ,
In my application , i am using RTC1 for RTOS and RTC2 for Running a time calibration andRTC0 for Softdevice but parallelly i need to add Lbs service which includes...
Hi there,
I wanted to test Matter/Thread networks using the nRF5340DK I have.
I downloaded the nRF Connect SDK through the Toolchain manager.
I tested the blinky app...
Hi,
I have an unusual requirement where the current constraint device needs to the controller and passively scan. My understanding is the best way to estimate the current...
Hi Nordic Semi
I have implemented a basic BLE peripheral on a nRF5340 using the nRF Connect SDK 1.7.0.0.
The product we are developing have strict power consumption requirements...
I've been able to port the DFU process into a C# app running within a Linux gateway.
I'm using the buttonless without Bonds service to enter DFU mode.
The problem I have...
I am trying to find information on this and it is not clear.
Is it safe to perform FDS read operations (i.e. fds_record_open(), fds_record_find() and fds_record_close()...
Device: nrf52833
SD S140
Application - Central Host, based on uart central sample project
The peripheral device needs to deliver a block of data (10-20K bytes) to the...
Hi,
First of all, I am currently trying to merge several projects and some of the project were using older versions of the drivers. Then I noticed that the oldest update...
Hi,
I am trying to get a GPS reading on the NRF9160DK. I have tried both the GPS sample (no SUPL client) and the A-GPS sample , but with neither sample projects I manage...
