Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
As below, BLE Data RX works fine, but TX doesn't. When does this happen?
Currently BLE connect/disconnect and RX is working fine. The power does not turn off due to this...
Hello: I am trying to design a project about a type of sensor powered by high accuracy battery which is using the nRF52832 chip in a custom board. To use the battery energy...
Hi
My requirement is to upgrade the application firmware on the nRF52840-DK from another processor using SPI interface, and I am trying to understand the code to plug-in...
I'm developing a beacon application using the Fanstel BT832AF, which uses the nRF52810 internally. This unit is mounted to a custom board, but before raising a private ticket...
As instructed to post here by We're using Zephyr on at least 4 of our products and have thousands of boards with NRF chips in the pipeline; we're trying to get the consumption...
I'm trying to install nrfutil, but for some reason the installation is unsuccessful.
After installing python and the executing pip install nrfutil, restarting both the shell...
Hello,
when my application runs, from time to time I see the following:
[00:00:29.000,000] <debug> nrf_sdh_ble: BLE event: 0x26. [00:00:29.000,000] <error> app: ERROR...
Hi Nordic team
Customer SecuX failed to use JLINK V9 to update modem firmware to Thingy91 and customer nRF91 board both.
But, JLINK V9 can program merged.hex file(application...
I want to bring up a secure bootloader with support for ECDSA and SHA-256.
I am having a hard time coming up with a combination of SDK components (frontend, backend), external...
Hi All
I'd like to implement "Fast advertising" with SDK14.10
Q1: I add some code in advertising_data_set() to do fast advertising, is that correct ?
Q2: If want...
Good afternoon. I have the Zephyr gsm_modem sample up and running for my GSM modem and a PPP connection is established to the cellular network. The example does nothing further...
After I write bonding data to flash memory (SoftDevice has been disabled before the write) I get an APP_ERROR:ERROR:FATAL. But I do not know what is causing it. I do an NRF_LOG_DEBUG...
Hi,
We added new commands for code from openthread and generated .hex file by "make -f examples/Makefile-nrf52811 NCP_SPI=1 FULL_LOGS=1 && arm-none-eabi-objcopy -O ihex...
We are planning to develop BLE and Bluetooth Mesh products using nRF52840. I have a couple of questions in use of Zephyr. 1) What is advantage of building BLE or Mesh on Zephyr...
Hi,
I tried to build the ble_app_uart example for nRF52820/s140. In my project I need to use C++ modules.
My usual approach that worked so far:
Take an example project...
