Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I am developing on a nRF52832 with S132 softdevice using Segger and SDK15.2.0. I am doing some tests with the Flash memory, and my goal is to have some const variables...
We are preparing an application to enter production and seeking to harden it to protect against unexpected system lockup.
The application is a datalogger peripheral based...
Hi,
In the Light Switch Example, on-off instruction was send to either even or odd address, may I know how can I cancel this action so that I can send the on-off instruction...
Hi,
I am using nRF mesh Android app version 1.0.3 and nRF mesh IOS app version 1.0.2
I have flashed the devices with light-switch example application under nRF5 SDK for...
Hi, I have pca10059 dongle. I soldered goldpins to swdio and swdclk lines to be able to flash it using external nrf dk. So I connected external jlink programmer and was able...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
Hello All,
I am using NRF51822 controller in my design.
I want to monitor battery voltage using ADC pin with voltage divider.
I have LIPO battery with 3.7V and 200mAH...
Hi Nordic Support, community,
After I flashed, the connectivity hex, ble_connectivity_s140_usb_hci_pca10059.hex from the SDK v15 downloaded after executing the patch on...
development software, with versions (SDKs, IDEs, SoftDevices, ...):
Computer platform, with versions (Windows/Linux/OSX, ...) Windows 10 Pro x64
hardware revisions (chip...
Hi,
I am trying to make a weather station with nRF52 feather and BME280. Currently I am making a measurement program. The base code is Custom:Heart Rate Monitor Example...
Hi friends I use nrf51822 with sdk12.3 version and I want to use infrared receiver.
What method should I use to write the infrared receiver code?
Also, does nrf51 have...
Hi,
I'm able to send arbitrary information to the host using generic HID descriptor (uses vendor defined page). There is no driver issue. I'm also able to connect to the...
I am currently downloading softdevice (S140) on our custom board using P19 connector on nRF52840 DK. Our custom board also has nRF52840. It seems the dsoftdevice is downloaded...
nRF52832 & nRF52810 don't support the Bluetooth 5 Range Extension (Coded PHY):
https://devzone.nordicsemi.com/f/nordic-q-a/39532/is-it-only-nrf52840-s140-which-support-bt5...
