hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Is there any release timeline for a Nordic Thingy based on the nRF52840? Does anybody know of an open-access beacon that incorporates the nRF52840? Thank you.
I'm trying to communicate with a single NeoPixel ( WS2812B) using the PWM module.
I've configured a sequence array with the compare values necessary to turn on the red and...
Hi everyone
I'm trying to get the status of button by using the bsp_event_callback_t, but my application crashes when I push on any button.
Test environment: Freertos...
Hi Team,
For the board having Linux Host having nRF52832 interfaced over UART, what are the maximum number of BLE devices can be connected?
As per my understanding it...
Hello, this is Kwonjoon Lee, beginner of BLE development.
I successfully installed pc-ble-driver (c/c++) in accordance with Git-Hub guide ( https://github.com/NordicSemiconductor...
Hello,
This is Jahnavi. I am having nrf52 DK development kit and with that development kits I am using light switch example to connect the boards as mesh network. How...
Hallo everyone,
I'm using Eclipse IDE for C/C++ Version 2018-12 (4.10.0), my OS is Ubuntu 18.04.2 LTS and my hardware is the NRF52840 DK. I'm using the GCC C and C++ Compiler...
Hello:
I have nRF9160 SIP custom board. The pins on custom board almost the same as nRF9160DK.
I can run lte_ble_gateway sample on nRF9160DK without problem:
But...
I followed nRF Connect SDK 0.3.99 to test nRF9160 LTE Sensor Gateway.
I successfully completed steps 1 thru 10 in the Testing section
It was successfully connected...
Hi all,
I am communicating with a sensor through UART using APP_UART on a custom board (nrf52840) through the nrf52 DK. I can send and receive commands to and from the sensor...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
We are using nRF52840 with BLE and 802.15.4 concurrent with S140 SoftDevice. There are two functions to set the transmit power for each radio protocol:
sd_ble_gap_tx_power_set...
Hi all!
In my application I would like to use LESC OOB pairing between two S132 SoftDevices. But there is one thing that I'm not sure of: I only have the (wired) OOB channel...
Thank you for considering my problem!
I have maybe have seen a working Micro SD card with the 52840DK, but have not been able to produce it on my board. 52832. I am using...
I understand that the nrf9160 product is still in pre-release. I did have a look at the gps receiver section in the DocLib.
For future planning it would be very helpful...
