Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
hello everyone：
I use nordic APPtoolbox to test DFU ,android toolbox can DFU，but ios toolbox can't DFU
1、 i use sdk9.0 dfu project,and sdk9.0 ancs project
2、 blog.chinaunix...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
Where to get Master Control Panel 3.4.0 source code? Our project is related to creating proprietary BLE profile's. We have some idea on how to program a sensor device...
Hi,
on my board I have a nRF51 and a LIS2DH accelerometer. I want to enable an interrupt pin INT1, so if the LIS2DH sends an interrupt event (pin change from high to low...
I am using example->peripheral->uart(KEIL version MDK 5) in SDK11.0 . Because my 52832 board is a new one I made, I changed RX_PIN_NUMBER and TX_PIN_NUMBER to 9 and 8. CTS_PIN...
Hi,I'm using mpu9150 imu sensor with nRF51822 EK kit, i want read that sensor values i.e acceleration, gravity, yaw,pitch,roll values in keil ide ,how i can do that? Can any...
Hi,i'm using the nRF51822 with the IMU 9150 sensor, i'm using the github.com/.../nrf5-mpu-examples git repo for my sensor. while i try to read the values of sensor in Tera...
I am trying to flash TCP-Server example from IOT SDK from Eclipse.
Project builds without errors.
But I am getting this warning message in Eclipse console when I flash to...
s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
I want to use the Central Glucose Service, how do i modify the "ble_central/ble_app_hrs_c" example code?
int main(void...
I wanted to use MQTT example with nrf52 DK board.
and I uploaded MQTT firmware which is located MQTT example folder in iot SDK.
www.youtube.com/watch
I tried to follow...
Hi,
I want to implement handler for undefined instruction fault. According to Cortex M4 documentation (ARM DUI 0553A subchapter 2.3.2 "Exception types") this fault leads...
Hi everyone,
I've been experimenting compiling my project with Clang and have run into some issues with the supervisor calls and their wrapper in nrf_svc.h.
Without...
Hi,
I want to implement simple module:
gpiote event on pin change (around 6.7MHz signal)
Route gpiote event through PPI to increment counter
Toggle GPIO pin...
