I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi Nordic,
For my application, I want to have the absolute acceleration (without gravity) from a MPU6050. I know that this device can do that because it has 6 axis and...
Hi,
I am trying to maintain a single bit of information through a power-on reset event (sd_nvic_SystemReset();). I am trying to do this through the configuration of an...
Hello,
I'm having problems running the DFU over serial bootloader example. The nrfutil command to update the application fails with message "timed out waiting for acknowledgement...
Hi together,
I'm trying to scan for BLE Beacons and I got the problem that if I set setReportDelay() to a value unlike zero, the onBatchScanResults() method is called and...
Hi,
I am trying to measure the current consumption on my application, and measured some quite high values even after calling sd_app_evt_wait().
After reading through some...
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We have sold over 8000 devices of our first product. Currently we are...
Hello,
My problem is to much current c.a. 40uA in POWER OFF mode. Below attach code:
void power_down()
{
nrf_gpio_pin_clear(22); // Wylacz mostek tensometryczny
nrf_delay_ms...
With nRF52832 DK I have managed to compile this blinky example:
#include <stdlib.h>
#include <stdint.h>
#include <stdbool.h>
#include "nrf_delay.h"
#include "nrf_gpio...
I am getting no radio (as in not being able to pick up advertisements packets) from my custom nrf52832 board. The antenna design is a hack so I am not looking fo stellar performance...
We are looking in to developing a generic class to connect and handle our BLE devices for use on mobile devices such as Android and iOS.
Now since we want to have as less...
Hello Experts,
I am running the following examples to test the DFU bootloader in gcc and eclipse environment.
bootloader_secure/pca10040(Bootloader) and experimental_ble_app_buttonless_dfu...
I found a problem of the nRF51822 in boot state.
Power on reset is not executed occasionally when used dying battery.
The problem occurs in the following steps:
...
Hi All,
I'm having a BTLE_CONNECTION_TIMEOUT when I connect the device in Master Control Panel 3.10.0.14 while the chip is not in debug mode.
The device connects without...
Hi
I am trying to upgrade the firmware in a BL652 using a Segger Jlink Edu.
The BL652 is powered with 3.3v using a regulator off the JLink 5v output.
I had poor/unreliable...
