I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I want to read the onboard (dev board) buttons which i believe are P13-P16. I want to know the working code.
uint32_t app_button_is_pushed ( uint8_t button_id,
bool *...
I am trying to estimate the memory usage of the s132 v3.0.0 running on a nRF52832. I am interested on acting only as a peripheral with one link at a time only. From app_ram_base...
Implementing my own protocol stack with low-level programming of the radio, can I broadcast by simply programming all units to receive the same address?
No addresses (such...
Hi,
I am trying to use the sdk version 9 for the NRF51 to take ADC samples and trasmit it over BLE over UART found in the link: github.com/.../nRF51-SDK-9-0-0
I downloaded...
For example,
CFLAGS += -DCONFIG_GPIO_AS_PINRESET
CFLAGS += -DNRF52_PAN_12
CFLAGS += -DBLE_STACK_SUPPORT_REQD
Where are -DCONFIG_GPIO_AS_PINRESET, -DNRF52_PAN_12...
Hi,
I faced a strange kind of issue while i was burning the same code on nrf51442 and nrf51882 chip. The code is running fine on the nrf51442 chip but the code wasn't running...
My µvision crashed during programming and will no longer respond to trying to program it. It boots into the bootloader mode. My computer sees it but the precompiled binaries...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
Hello,
i'm searching for informations about calibrating the SAADC of the nRF52. And i have read here: Link
For nRF52, there are no calibration
values that I know of...
Hi Sir/Madam
I wrote a small program for low current verification on nrf51822 development kit with starter mother board.
The program is based on "blinky_example" project...
Hello to all,I have developed a board using the NRF51822;
Currently I am using SDK v11, S130 v2.
I have a problem in my bootloader, since bootloader_app_is_valid (from...
