Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Thank you very much in advance for any help.
I am attempting to upload an example firmware on a nRF52832 with the s132 softdevice BLE stack and the example DFU bootloader...
just like
github.com/.../nrf52-mpu-easydma-using-timers-and-drivers
we add a sensor, and try to read 2 sensors by 3 command in i2c.
is it possible to still using ppi...
Hi Friends,
I am beginner for nRF51822 and I install uVision 5.20 to create program for this chip.I can't see this chip on device selection table when new project creating...
Hi,
I've recently bricked my nrF51822 Beacon Kit ( www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit)
...by uploading some bad firmware. I can no longer program...
I am beginner for nRF51822.I installed uVision 5.20 to program nRF51822 chip.I could not see nRF51822 chip on chip selection guide of uVision software.Also I need some example...
Hello.
I've been trying to use the nRF Beacon for Eddystone app to configure a nRF52 devkit. The idea is to configure a slot as EID and register it to my google account...
Hi there,
I know 3V lithium batteries (Lithium Manganese Dioxide) batteries would be perfect for the nRF51822, but we're wondering if Lithium Thionyl Chloride (Li-SOCl2...
Hello,
is there a softdevice for the nRF52 which supports the proprietary wireless protocoll of the radio nRF24L01+? I only find ones which supports Bluetooth 4.0 and ANT...
Hello,
i have a very small device with bluetooth connection which send data every 20ms to a smartphone. The adc is sampling 100 times per second. Because of the small design...
Morning
I was just wondering if anyone knows which types of Bluetooth devices work with the nRF Toolbox for iOS and where to buy them - proximity etc.
Iain
Dear Nordic Engineers!
I am using the nRF51422 QFACA1 on custom boards and planning to migrate from SDK8.0.0 to SDK11.0.0
My application is using the S120 soft device...
Hi all! I want to send data from a beacon (nrf51822) to a Pic microcontroller with the RS232 standard, what function should I use to send data? I have already tried but it...
hello.
I want use I2C program.
so, I used twi_master_using_app_twi example.
SDA is output only 1byte(0x21).
I need to output a continuous 5byte.
Where do I need to modify...
Although the login form in the right side-bar works, the on in the main page does not. To reproduce:
Log out,
Click on 'Sign in' on the side bar
It should take...
Hi,
I am trying to use PPI for generating a output of lo to hi when NRF_RADIO->EVENTS_READY occurs.I want to generate on the same pin hi to lo when NRF_RADIO->EVENTS_END...
