When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
We have found what appears an easily reproducible bug in nrf_serial_read.
Reproduce as follows:
* PCA10040
* SDK 15.3
* SES
* Example project peripheral serial ...
Hi everyone,
I'm working on the nrf52832 using the SDK 15.2.0 with freertos and the application I am developing requires to save data on the flash while the BLE stack is...
Hi
When a GATT Table is created using the softdevice api, how do specify that a service or characteristic shall have a minimum key size of X so that if the current encrytion...
I am currently developing an app on Android studio that should detect nrfDongle.
I successfully uploaded UART software from SDK 13.0.0 to dongle and it is being successfully...
Hello, i want to know is it possible scan iBeacons with a node using nrf mesh with proxy features like the light switch node server example? if this is, how i could start...
Hello.
I have pa/lna on my device. It works properly in application (rssi is about 30 dbm). But when application goes into bootloader (dfu over ble using nrfconnect on android...
Hi, I'm using the nrf connect mobile app and I want to connect multiple devices to the advertising device and I want them all to access the same characteristic at the same...
When I open SES it says that it cannot detect any j-link so it asks me to buy license. But shouldn't my nrf52840 dk board have on-board j-link that SES should detect? I check...
Hi,
as I understand (and tried), in order to get low power consumption on the NRF91, I need to to get CONFIG_SERIAL=n.
However , I need the uart to be enabled (for short...
Hi - I am wondering what is the power optimal way to read/write with the TWI module. I do a tx and rx with the TWI interface. I have something like this, from the examples...
Hi,
We have just almost finished develop a product which used nrf52840 as a data hub, a wifi module connect to nrf52840 through uart, and baudrate set to 460800, and also...
Hi ,
I am using the example "ble_app_uart".
I enable uart while receiving data from nus handler and turn it off after transmitting.
After I mondified the code, it can...
When trying to write the bootloader hex file to the device with nRFgo Studio, the following error message is displayed.
[nrf52840_xxaa_s140.hex programming failed: This...
Hello
I'm using SDK 15.2 on nRF52 DK to test the ble_app_multirole_lesc example.
I downloaded the code to nRF52 DK to act as central.
I commented the scan_start() function...
