Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I am trying to get the application to enter DFU via the buttonless DFU service using SDK 15.2. It appears to be stuck because of an SVC call not returning. Both application...
Hi :)
I would like to test the nRF52840-Dongle in a Raspberry Pi 3B+ OS = Rasbian (the bluetooth 5 features: 2Mbps and Long range). but unfortunately I didn't find a nRF...
I'm looking for a gateway (or BLE 5.0 device that can connect to a gateway, e.g. USB dongle) that uses the nRF52 series solutions with an amplifier that brings the transmission...
Sir
We have a client that is using two NINA B3 (uses a NRF52840), one central and other peripheral. The peripheral is sending advertising packages, but the central is only...
Hi I'm very interested in studying this protocol, and I'm testing with nrf52832 kit development, loading the example "bike power meter tx" and app on android "ant + plugins...
Hi,
I'm using NRF52832 and a core adaptation for Arduino IDE. In my project I'm using both TWI and SPI interfaces. If for TWI I manage to reduce the current during sleep...
Hi everyone,
I am using a chip nRF52832 reading data from LIS2DH12 via TWI (all in a custome boad), then data will be send to Master nRF52832 DK ia BLE_NUS. However, when...
I have a new nRF52840 Dongle which seems to have either had a hardware failure while updating its bootloader or the updating was unsuccessful and now the device does not flash...
To do some test, I need micros(). This is the reason why I couldn't use RTC or app_timer.
When I tried timer example(nRF5_SDK_12.2.0_f012efa\examples\peripheral\), I could...
Hello, I need to use PWM to control GPIO and integrate it to work on simple COAP server app using nrf52840 DK.
I used "pwm_simple" example from SDK (not Thread/Zigbie SDK...
Hello.
When I try to initialize provisioning bearer gatt with turned on the proxy, provisioning bearer is reconfigure the mesh_gatt which it will not work with proxy anymore...
Hello,
I started developing a Thread-Solution with my NRF52840-DK. Now I'm searching if there is a Message Sequence Chart (like for the BLE solution) also for the Thread...
Hi,
I'm testing the below example code, found on devzone, on mesh sdk 2.2.0.
I'm experiencing a strange issue on the read side. On the first read after the write I always...
Hi,
I have an application (central mode) which regularly connects to a number of clients, read characteristics and then disconnects again.
Whenever there is an unintended...
I'm have nRF52 DK, wish use nrfutil (v4.0.0) to update target firmware. Works fine when using -n "Target Name", but I get a "Device not found" when trying to use parameter...